Metrel A 1632 EVSE Charging Station and Lead Adaptor

The Metrel A 1632 eMobility Analyser is a professional, multifunction test adapter designed for comprehensive verification of Electric Vehicle Supply Equipment (EVSE) and EV charging cables. Engineered for both safety and functional testing, it enables technicians to diagnose charging stations, simulate EV behaviour, and verify communication signals between the EVSE and an electric vehicle.

Supporting both Mode 2 and Mode 3 charging systems and Type 1/Type 2 EVSE interfaces, the A 1632 delivers accurate CP/PP simulation, mains fault simulation, and detailed diagnostic evaluation. When paired with compatible Metrel instruments, it offers full Bluetooth-enabled remote operation and advanced reporting capabilities.

Monitoring communication between the EVSE and the EV (simulated electric vehicle) during charging.

Use with Metrel Alpha EE MI3340 / Omega MI3365 PAT Testers

Mode 2 (Portable)

• Type 2 charging leads (wire continuity, insulation, wiring)
• Type 2 charging leads (leakage current — requires clamp sold separately)
• Type 2 RCD testing (trip time, trip current)
• Type 2 CP error state simulation
• Type 2 charging current indication
• Type 2 mains supply fault simulation (L open, N open, PE open, L–PE cross, external PE voltage)
• Type 2 resistance coding (PP)

Mode 3 (Fixed Wall Box)

• Type 2 RCD testing (trip time, trip current)
• Type 2 CP error state simulation
• Type 2 charging current indication
• Type 2 mains supply fault simulation

Mode 3 (Leads)

• Type 2 charging leads (wire continuity, insulation, wiring)
• Type 2 charging leads (leakage current — requires clamp sold separately)
• Type 2 resistance coding (PP)

Use with Metrel MI3152 / MI3155 Installation Testers

Mode 2 (Portable)

• Type 2 charging leads (wire continuity, insulation, wiring)
• Type 2 charging leads (leakage current — requires clamp sold separately)
• Type 2 RCD testing (trip time, trip current)
• Type 2 CP error state simulation
• Type 2 charging current indication
• Type 2 mains supply fault simulation (L open, N open, PE open, L–PE cross, external PE voltage)
• Type 2 resistance coding (PP)

Mode 3 (Fixed Wall Box)

• Type 2 RCD testing (trip time, trip current)
• Type 2 CP error state simulation
• Type 2 charging current indication
• Type 2 mains supply fault simulation

Mode 3 (Leads)

• Type 2 charging leads (wire continuity, insulation, wiring)
• Type 2 charging leads (leakage current — requires clamp sold separately)
• Type 2 resistance coding (PP)

Electrical & Diagnostic Measurements

• Nominal system voltage: 100–440 V AC
• Frequency range: 0 Hz, 14–500 Hz
• Phase rotation: 1-2-3 or 3-2-1
• CP/PP voltage measurement: −19.99 V to +19.99 V
• Duty cycle measurement: 0.1–99.9 %
• Charging current indication (I_EVSE): 0–99.9 A (calculated)
• Disconnection time test: 0–399 ms (typical accuracy ±1% + 5 digits)

Simulation Functions

• PP resistor simulation: NC, 13 A, 20 A, 32 A, 63 A, 80 A
• CP state simulation: States A, B, C, D (no EV, EV connected, EV charging, EV charging with ventilation)
• Fault simulations: L1/L2/L3 open, Neutral open, PE open, L–PE crossed, external voltage on PE, CP diode short, CP–PE short, PE open (output side)

General

• Battery: 7.2 V Li-ion, typical 4 h charging time
• Battery operation time: > 18 h in diagnostic operation
• Protection / measuring category: 300 V CAT II
• Ingress protection: IP65 (case closed), IP40 (case open), IP20 (mains socket)
• Dimensions (W × H × D): 36 cm × 16 cm × 33 cm
• Weight: approx. 5.2 kg (without accessories)

The A 1632 eMobility Analyser integrates smoothly with a range of Metrel installation and PAT testers, enabling full functional, diagnostic and electrical safety testing capability:

• MI 3152 Instaltest XC
• MI 3155 Instaltest XD
• MI 3340 Alpha EE XA PAT
• MI 3365 Omega PAT
• MI 3325 MultiServicerXD

These instruments support Bluetooth communication with the A 1632 for remote control, automated test sequences and streamlined reporting workflows.

• A 1632 eMobility Analyser
• Type 2 male plug adapter with long CP pin (2 m, Metrel connector)
• 1-phase EU to 3-phase CEE (16 A) mains cable (2 m)
• 2 mm banana to 4 mm cascade banana adapter (1 m)
• Protective bag for accessories (mounted on the case)
• Instruction manual
• Calibration certificate

The A 1632 eMobility Analyser is covered by Metrel’s standard manufacturer warranty against defects in materials and workmanship. Warranty coverage does not extend to damage caused by misuse, unauthorised modification or mechanical abuse. For warranty and out-of-warranty service, please contact your authorised Metrel distributor or service centre.